Absorbent Selection and Chemical Compatibility Guide

Use this absorbent selection and chemical compatibility guide to match common fluids to an absorbent type: oil-only, universal, or hazmat / chemical.

This is general guidance only. Always defer to the Safety Data Sheet (SDS) of the spilled liquid, and to your site procedures, for compatibility, PPE, fire risk and disposal. When the chemical is unknown, treat it as aggressive until you can identify it.

Quick selection

  • Oils and fuels (motor oil, hydraulic oil, diesel, gasoline): start with oil-only absorbents. Universal also picks up oil if that is what you already have on hand.
  • Coolants, antifreeze and other water-based fluids: use universal absorbents. Oil-only absorbents typically repel water and will not pick these up well.
  • Acids, bases, solvents, oxidizers, or unknown chemicals: use hazmat / chemical absorbents and check the SDS before you start.

Fluid and absorbent table

Fluid Recommended absorbent Notes
Motor oil Oil-only (universal also works) Oil-only can skim petroleum off water. See oil-only mats and oil-only spill kits.
Hydraulic oil Oil-only (universal also works) Treat as a petroleum oil unless the SDS says otherwise.
Diesel or gasoline Oil-only (universal also works) These are flammable. Control ignition sources and follow the SDS. Oil-only is useful when fuel is on water.
Coolant or antifreeze Universal Water-based. Oil-only absorbents typically will not pick them up well. See universal mats.
Water-based fluids Universal Includes many process waters, wash water and similar liquids. Confirm the SDS for additives.
Cutting fluids Universal; confirm the SDS Some metalworking fluids are water-based; others are oil-based. If the SDS describes an oil-based fluid, oil-only may be appropriate. When in doubt, use universal or hazmat as the SDS directs.
Acids HazMat / chemical Never use cellulose or organic absorbents (such as untreated cotton, peat or sawdust) on oxidizers or strong acids. See hazmat absorbent mats and hazmat spill kits.
Bases or caustics HazMat / chemical Check the SDS. Some sites also keep a neutralizer that their plan specifically authorizes; do not improvise one.
Solvents Often hazmat / chemical; confirm the SDS Compatibility and fire risk vary widely. Some solvents can be handled with a universal absorbent; others need a chemical-compatible product. Follow the SDS.
Aggressive or unknown chemicals HazMat / chemical Do not use oil-only or untreated cellulose / organic absorbents. Identify the material, check the SDS, and wear the PPE your site plan requires.

Important compatibility notes

  • Always check the SDS before you select an absorbent, PPE or a disposal method.
  • Never use cellulose or organic absorbents on oxidizers or strong acids.
  • Oil-only absorbents are a poor match for coolants, antifreeze and other water-based fluids because they are made to repel water.
  • If more than one fluid type is present, or the liquid is unknown, start with a hazmat / chemical absorbent unless your EHS team directs otherwise.
  • Used absorbents take on the hazards of the liquid they hold. Store and dispose of them according to the SDS and local, state and federal rules.

Shop absorbents, kits and PPE

Need a kit by fluid and location? Use the spill kit finder or the spill kit sizing calculator. For cleanup steps, see How to Clean Up an Oil Spill. Planning forms are in the free EHS forms library, including a spill response SOP template.

WellKept Supply is a distributor, and lead times vary by product.

FAQ

What is the difference between oil-only, universal and hazmat absorbents?

Oil-only absorbents are made to pick up petroleum oils and fuels and typically repel water, so they can skim oil off a wet surface. Universal absorbents are the usual choice for coolants, water-based fluids and mixed everyday liquids, including many oils. HazMat or chemical absorbents are for acids, bases, solvents, or aggressive or unknown chemicals. The SDS of the spilled liquid is the authority, not this table.

Can I use oil-only pads on coolant or other water-based fluids?

Usually not well. Oil-only absorbents are designed to repel water, so they tend to leave coolants, antifreeze and other water-based fluids behind. Use a universal absorbent for those liquids, or a hazmat absorbent if the SDS calls for it.

Why shouldn't I use cellulose or organic absorbents on strong acids or oxidizers?

Cellulose, cotton, peat, sawdust and similar organic absorbents can react with oxidizers and with some strong acids. That reaction can create heat or other hazards. For acids, bases, oxidizers, or unknown chemicals, use a compatible hazmat or chemical absorbent and follow the SDS.

What if the chemical is unknown?

Treat it as an aggressive chemical until you can identify it. Use a compatible hazmat or chemical absorbent, wear the PPE your site plan requires, keep people back, and consult the SDS or your EHS team as soon as you can identify the material. Do not use oil-only or untreated organic absorbents on an unknown spill.

Do I still need to check the SDS?

Yes. Compatibility, PPE, fire risk and disposal all depend on the specific product. This page is general guidance only and does not replace the SDS or your site procedures.

Related tools: Spill Kit Sizing Calculator and the Secondary Containment Calculator.

Provided by WellKept Supply as a general reference. Adapt to your site and local, state and federal requirements. This tool does not guarantee regulatory compliance.